Looking for:
Dt466e service manual download |
1997-2000 International DT466E, DT530E Engine Wiring Diagram.Dt466e service manual download
Quick Links Download this manual. Table of Contents. Previous Page. Next Page. Printed in the United States of America Follow all warnings, cautions, and notes. Page 4 Appendix E — Instruction Sheets EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Page 8 Make sure all tools, parts, and service equipment are removed from the engine and vehicle after all work is done. The open crankcase breather EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page 17 Water inlet elbow Flat idler pulley assembly Front cover front half Water pump pulley EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Page 18 Page 19 Power steering pump High-pressure oil pump Lifting eye Oil pan assembly assembly EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page 20 Coolant drain plug underneath compressor bracket location EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Page Air Management System — single or dual element Exhaust manifold Intake manifold Page 26 ECM decreases the duty cycle to the control module. The IC has three Hall effect position sensors to monitor valve movement. Page 31 IPR valve will operate from programmed default values. This is called Open Loop operation. Page Fuel Injectors Spool valve control valve EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Page 36 High-pressure oil is deadheaded against the spool valve. Page Fuel Supply System Fuel inlet 4 assembly assembly Low-pressure fuel supply pump Page 39 Plug or EFP sensor optional Water drain valve assembly Another drain valve in the bottom of the housing drains strainer cavity.
Page Engine Lubrication System Pick-up tube crankcase Oil pan assembly EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. The oil is then internally EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page 43 if equipped. Water inlet to front cover and assembly water pump EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Page 45 The EGR cooler receives coolant from the front cover. Page Engine And Vehicle Sensors Page 55 A remote accelerator or throttle device can be used in addition to the accelerator pedal. Page 56 A voltage input switch supplies the ECM with a voltage when it is closed. Page 59 A gallery. Page 61 Figure 50 Brake pressure relief valve in high-pressure oil rail Front of engine Brake pressure relief valve EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Page Component Removal 1. Page Oil Filter The oil cooler drain tube is trapped between the oil system module and the front cover. Page Engine 5. Slowly release tension from engine hoist. Page 74 Turbocharger control module Compressor outlet Oil drain port Page Removal 4. Disconnect electrical harness from VGT actuator. Page Cleaning 4. Clean remaining gasket material from mounting manifold. Page Inspection 6. Connect electrical harness to VGT actuator.
Intake manifold to mixer gasket EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
Disconnect the EBP tubing nut at exhaust manifold. Page Cleaning And Inspection 3. Check manifold for cracks and damage. Replace special torque value Table 8. Page Installation 4. Torque the exhaust manifold bolts in the following the exhaust manifold gasket over these two bolts.
Page 92 7. Install intake plug assemblies, if removed M12 and tighten to the special torque value Table 8. EGR valve assembly O-ring 3 Gasket, hot side EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page EGR cooler and the rear half of the front cover.
Page Remove two bolts M8 x 30 retaining the EGR cooler to the exhaust manifold. Page Cleaning Egr System Components Page 3. Page 8. Page Guidelines, page Using P or equivalent, lubricate O-ring on adapter.
Page 9. Retighten constant tension EGR hose clamps to the special torque Table Remove EGR rear mounting bolts. Page Installation 8. Put O-ring seal on new EGR coolant return adapter tube. Page Special Service Tools Page Description The valve guides and valve seats are replaceable.
Intake valve Valve guide inserts Rear lifting eye Valve assemblies EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Page Lower support washer 6 Rocker shaft plug 2 12 Roller tappets 12 EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
System, page Page Removing Rocker Arm Assembly Make sure that you have these washers for installing the rocker arm shaft. Figure Measuring cam lobes with micrometer EGES Read all safety instructions in the "Safety Information" section of this manual before doing any procedures. Remove and discard 26 cylinder head mounting bolts M15 x Page Cleaning 1. Page Rocker Arms Replace the adjuster screw if excessive wear is replace the rocker arm.
Be sure to inspect the found. Page Cylinder Head Cracking 2. Spray dye penetrant on the gasket surface of the cylinder head. Leave the dye penetrant on for minutes. Page Pressure Check Cylinder Head If leakage is observed at any port or the upper and lower deck, replace the cylinder head.
No comments:
Post a Comment